Theses

Permanent URI for this communityhttp://197.255.125.131:4000/handle/123456789/22146

A long essay or dissertation or thesis involving personal research, written by postgraduates of University of Ghana for a university degree.

Browse

Search Results

Now showing 1 - 6 of 6
  • Item
    Photocatalytic degradation of Rhodamine dyes using zinc oxide nanoparticles
    (Materials Today: Proceedings, 2020) Dodoo-Arhin, D.; Asiedu, T.; Agyei-Tuffour, B.; et al.
    This paper presents the synthesis of nanocrystalline zinc oxide (ZnO) particles via the sol-gel method using zinc acetate as a precursor. The calcination temperature of the ZnO was varied to determine its effect on particle size. The resultant samples were characterized using X-ray diffraction (XRD), Fourier Transform Infrared (FTIR), UltraViolet–visible Spectroscopy (UV–Vis) and Scanning Electron Microscopy (SEM). Nanocrystalline wurtzite ZnO particles with crystallite sizes ranging from 16 nm to 30 nm were produced. The Energy Band gap of the synthesized zinc oxide nanoparticles decreased with increasing calcination temperature and crystallite size. SEM Micrographs showed rice-like microstructure morphology of ZnO nanoparticles. The usage of the ZnO nanoparticles as a photocatalyst was also explored in the degradation of Rhodamine B dye using UV light, with particular attention paid to the effect of particle size and catalyst load on the degradation efficiency of the dyes. The nanoparticles calcined at 400 C with a crystallite size of 16 nm resulted in the highest degradation efficiency of 95.41% when 0.2 g catalyst loading was applied. 2019 Elsevier Ltd. All rights reserved. Selection and peer review under the responsibility of the scientific committee of the International Symposium on Nanostructured, Nanoengineered, and Advanced Materials
  • Item
    Modified nanostructured titania photocatalysts for aquatic disinfection applications
    (Materials Today: Proceedings, 2020) Dodoo-Arhin, D.; Bowen-Dodoo, E.; Agyei-Tuffour, B.; et al.
    According to SDG 6, everyone on earth should have access to safe and affordable drinking water. In sharing water-treatment technologies that lead to accomplishing this goal, it is imperative to devise ways of removing microbial contaminants such as E. coli from drinking water, especially in resource-limited settings that lack centralized water supply systems. One of the approaches is bacterial disinfection of water at the point of use. In this study, the bactericidal effects of the photocatalysis of titanium dioxide-based nanoparticles under UV and visible light are explored. Pristine and silver doped nanostructured mesoporous titanium dioxide (Ag-TiO2, TiO2) particles with high specific surface area and average crystallite domain size of 7.0–7.5 nm were prepared using the simple and cost-effective sol-gel technique followed by thermal treatment. The addition of Ag+ ions during the hydrolysis/condensation of the Ti(IV) molecular precursor led to the homogeneous dispersion of the Ag+ cations on the titania matrix. The As-prepared nanoparticles were characterized using X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) surface area analysis, Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), thermogravimetry, Fourier Transform Infra-Red (FTIR), and Raman Spectroscopy. X-ray diffraction, FTIR, and Raman spectroscopy confirmed that the crystalline structure of the TiO2 matrix corresponds to the anatase polymorph; however, the presence of the dopant led to an increase in the system disorder due to the rise in the concentration of oxygen vacancies. The As-prepared nanoparticles were used for Escherichia coli (E. coli) inactivation under dark and UV–visible light conditions. Under dark conditions, Ag-doped titania and pristine titania resulted in 95% and 64% E. coli population inactivity while under light conditions, 99% and 97% degradation respectively were observed. Taken together, these results demonstrate that, the synthesized TiO2 nanoparticles have promising applications in the light-mediated point-of-use inactivation of bacterial contaminants in water. 2019 Elsevier Ltd. All rights reserved. Selection and peer review under the responsibility of the scientific committee of the International Symposium on Nanostructured, Nanoengineered, and Advanced Materials.
  • Item
    Effects of substrates on the performance of optoelectronic devices: A review
    (Cogent Engineering, 2020) Asare, J.; Agyei-Tuffour, B.; Dodoo-Arhin, D.; et al.
    This review discusses the effects of substrates on devices fabricated for optoelectronic applications. It includes the types and characteristics of substrates, synthesis, and fabrication of substrates, and the influence of substrates on the optical properties, surface morphology, and current-voltage behavior of optoelectronic devices. The study showed that two main types of substrates: planar and textured are commonly used in the industry. Flexibility, semi-rigidity, and rigidity are characteristics of the substrates and they vary in modulus, transparency, and texture. Whereas glass and metal substrates can be produced via melt casting, polydimethylsiloxane (PDMS), polyethylene terephthalate (PET), etc are produced by crosslinking polymer base materials with curing agents. The mechanical and current-voltage characteristics are also shown for planar and textured substrate-based devices. The textured substrates showed ridges, wrinkles, and buckled surface morphology whereas the planar showed uniform and largely flat morphology. Textured substrates also recorded higher optical absorbance and improved device efficiencies than planar substrates. The molecular configuration of the polymer chains is edged-on for planar substrates and edge-on and face-on for textured substrates. The findings and their implications have been discussed to highlight the importance of substrates in the fabrication and performance of optoelectronic devices.
  • Item
    Awaso bauxite red mud-cement based composites: Characterisation for pavement applications
    (Case Studies in Construction Materials, 2017) Dodoo-Arhin, D.; Nuamah, R.A.; Agyei-Tuffour, B.; et al.
    This paper presents the development of Bauxite residue (red mud) based cement composite mortar blocks for applications in pavement construction. The experimental techniques considered include the structural, thermal, morphological, and microscopy analysis of the raw bauxite and red mud samples calcined at 800 °C. Composite mortar blocks of different batch formulations were produced and their physicochemical properties were investigated. The results show that the compressive strength of the as-prepared composite mortar blocks increased by ∼40% compared to the type M mortar strength of ∼2500 N/mm2 . The load-bearing applications of the composites are discussed to influence the adoption of the calcined red mud as a supplement in the production of low-cost Portland cement-based composite mortar blocks for the construction industry.
  • Item
    Layered Nanomaterials - A Review
    (2012) Yaya, A.; Agyei-Tuffour, B.; Dodoo-Arhin, D.; et al.
    Layered materials can become a myriad source of two-dimensional crystals if the layers can be separated from each other, for example via exfoliation. Potential applications for single-layer materials range from energy storage, electronics, and mechanical reinforcement of plastics, to life-saving applications such as drug delivery, medical imaging, and clean-up of toxic materials in the environment. Layered nanomaterials can be found naturally and can also be synthesized in the laboratory to suit certain specific applications. We describe here key layered materials including some naturally occurring (graphite, graphene, clays, layered hydroxides (LDHs)) and others that have been synthesized through chemical combination of some atomic species such as boron nitride (BN), transition metal oxides (TMOs), LDHs, and transition metal dichalcogenides (TDMs), along with a discussion of their properties and potential applications.
  • Item
    Application of Discarded Rubber Car Tyres as Synthetic Coarse Aggregates in Light Weight Pavement Concretes
    (American Journal of Materials Science, 2015) Dodoo-Arhin, D.; Mensah, S.A.; Yaya, A.; Agyei-Tuffour, B.
    The increasingly high cost of building construction materials is a major factor affecting quality housing delivery in Ghana. The current trend of continuous and increasing demand for these natural resources has necessitated extensive research into alternative low-cost construction materials such as recycled materials with comparable properties. The characteristics of concretes produced using locally available discarded rubber car tires as coarse aggregates have been investigated. Batch formulation of 0%, 25%, 50%, 75%, and 100% substitution of natural coarse aggregates with the rubber aggregates is considered. A comparison of the physico-mechanical properties of batch formulations by weight % and volume % have also been investigated. Generally, the compressive strength of the concretes decreased as the percentage of the rubber increased in the two batch formulations. At 25% replacement, the compressive strength of 9.26 N/mm2 (weight %), 11.56 N/mm2 (vol %) as compared to 14.80 N/mm2 and 24.00 N/mm2 respectively for the controlled program were obtained.