Theses
Permanent URI for this communityhttp://197.255.125.131:4000/handle/123456789/22146
A long essay or dissertation or thesis involving personal research, written by postgraduates of University of Ghana for a university degree.
Browse
24 results
Search Results
Item Photocatalytic degradation of Rhodamine dyes using zinc oxide nanoparticles(Materials Today: Proceedings, 2020) Dodoo-Arhin, D.; Asiedu, T.; Agyei-Tuffour, B.; et al.This paper presents the synthesis of nanocrystalline zinc oxide (ZnO) particles via the sol-gel method using zinc acetate as a precursor. The calcination temperature of the ZnO was varied to determine its effect on particle size. The resultant samples were characterized using X-ray diffraction (XRD), Fourier Transform Infrared (FTIR), UltraViolet–visible Spectroscopy (UV–Vis) and Scanning Electron Microscopy (SEM). Nanocrystalline wurtzite ZnO particles with crystallite sizes ranging from 16 nm to 30 nm were produced. The Energy Band gap of the synthesized zinc oxide nanoparticles decreased with increasing calcination temperature and crystallite size. SEM Micrographs showed rice-like microstructure morphology of ZnO nanoparticles. The usage of the ZnO nanoparticles as a photocatalyst was also explored in the degradation of Rhodamine B dye using UV light, with particular attention paid to the effect of particle size and catalyst load on the degradation efficiency of the dyes. The nanoparticles calcined at 400 C with a crystallite size of 16 nm resulted in the highest degradation efficiency of 95.41% when 0.2 g catalyst loading was applied. 2019 Elsevier Ltd. All rights reserved. Selection and peer review under the responsibility of the scientific committee of the International Symposium on Nanostructured, Nanoengineered, and Advanced MaterialsItem The physico-mechanical influence of dehydroxylized activated local kaolin: A supplementary cementitious material for construction applications(Case Studies in Construction Materials, 2019) Marfo, K.K.; Dodoo-Arhin, D.; Agyei-Tuffou, B.; et al.This work presents the effect of partially replacing metakaolin with Portland limestone cement to produce mortars for construction. Teleku Bokazo kaolin was explored as an SCM for the production of mortars. The hydration product between Portland limestone and metakaolin was studied. The kaolin was heat treated to form metakaolin and partially used to replace Portland limestone cement (PLC) in mortars to explore the optimum replacement and its mechanical and durability effect. The samples were characterized using X-ray diffraction (XRD) for phases and crystallinity of the kaolin. Fourier transform infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM) gave information on the functional groups formed during the hydration and structure and surface morphology respectively. The pastes and mortars produced were subjected to setting time, water absorption, flexure, and compression strength tests. The mechanical properties were observed to increase with increasing metakaolin replacements. Therefore, from the results obtained, it is suggested that a 20 % replacement of Portland limestone cement with Teleku Bokazzo metakaolin can be very suitable for construction applications.Item Hydroxyapatite ceramics prepared from two natural sources by direct thermal conversion: From material processing to mechanical measurements(Materials Today: Proceedings, 2020) Akpan, E.S.; Dodoo-Arhin, D.; Dauda, M.; et al.In this study, hydroxyapatite (HAp) was extracted from catfish bones (CB) and non-separated animal bones (NB). The bioceramic samples were prepared by a facile synthesis route and the representative scaffolds were prepared by cold compaction and sintered at 900 C, 1000 C, and 1100 C. To evaluate the properties of the produced HAp, X-ray diffraction (XRD) and Fourier Transform Spectroscopy (FT IR) analyses were carried out. The evaluation of the hardness of the representative bio-derived scaffolds was experimentally conducted while the fracture toughness and brittleness index were obtained by calculation using the hardness test parameters. The experimental data showed that as temperature increased up to 1000 C for CB, there was a consequential increase in hardness, while for NB, hardness values reduced throughout the sintering regimes. These gradients in mechanical measurements are ascribed to phase changes during heat treatment. 2020 The Authors. Published by Elsevier Ltd. This is an open-access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by nc-nd/4.0). Selection and Review under the responsibility of the scientific committee of the International Conference & Exposition on Mechanical, Material and Manufacturing TechnologyItem Modified nanostructured titania photocatalysts for aquatic disinfection applications(Materials Today: Proceedings, 2020) Dodoo-Arhin, D.; Bowen-Dodoo, E.; Agyei-Tuffour, B.; et al.According to SDG 6, everyone on earth should have access to safe and affordable drinking water. In sharing water-treatment technologies that lead to accomplishing this goal, it is imperative to devise ways of removing microbial contaminants such as E. coli from drinking water, especially in resource-limited settings that lack centralized water supply systems. One of the approaches is bacterial disinfection of water at the point of use. In this study, the bactericidal effects of the photocatalysis of titanium dioxide-based nanoparticles under UV and visible light are explored. Pristine and silver doped nanostructured mesoporous titanium dioxide (Ag-TiO2, TiO2) particles with high specific surface area and average crystallite domain size of 7.0–7.5 nm were prepared using the simple and cost-effective sol-gel technique followed by thermal treatment. The addition of Ag+ ions during the hydrolysis/condensation of the Ti(IV) molecular precursor led to the homogeneous dispersion of the Ag+ cations on the titania matrix. The As-prepared nanoparticles were characterized using X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) surface area analysis, Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), thermogravimetry, Fourier Transform Infra-Red (FTIR), and Raman Spectroscopy. X-ray diffraction, FTIR, and Raman spectroscopy confirmed that the crystalline structure of the TiO2 matrix corresponds to the anatase polymorph; however, the presence of the dopant led to an increase in the system disorder due to the rise in the concentration of oxygen vacancies. The As-prepared nanoparticles were used for Escherichia coli (E. coli) inactivation under dark and UV–visible light conditions. Under dark conditions, Ag-doped titania and pristine titania resulted in 95% and 64% E. coli population inactivity while under light conditions, 99% and 97% degradation respectively were observed. Taken together, these results demonstrate that, the synthesized TiO2 nanoparticles have promising applications in the light-mediated point-of-use inactivation of bacterial contaminants in water. 2019 Elsevier Ltd. All rights reserved. Selection and peer review under the responsibility of the scientific committee of the International Symposium on Nanostructured, Nanoengineered, and Advanced Materials.Item Effects of substrates on the performance of optoelectronic devices: A review(Cogent Engineering, 2020) Asare, J.; Agyei-Tuffour, B.; Dodoo-Arhin, D.; et al.This review discusses the effects of substrates on devices fabricated for optoelectronic applications. It includes the types and characteristics of substrates, synthesis, and fabrication of substrates, and the influence of substrates on the optical properties, surface morphology, and current-voltage behavior of optoelectronic devices. The study showed that two main types of substrates: planar and textured are commonly used in the industry. Flexibility, semi-rigidity, and rigidity are characteristics of the substrates and they vary in modulus, transparency, and texture. Whereas glass and metal substrates can be produced via melt casting, polydimethylsiloxane (PDMS), polyethylene terephthalate (PET), etc are produced by crosslinking polymer base materials with curing agents. The mechanical and current-voltage characteristics are also shown for planar and textured substrate-based devices. The textured substrates showed ridges, wrinkles, and buckled surface morphology whereas the planar showed uniform and largely flat morphology. Textured substrates also recorded higher optical absorbance and improved device efficiencies than planar substrates. The molecular configuration of the polymer chains is edged-on for planar substrates and edge-on and face-on for textured substrates. The findings and their implications have been discussed to highlight the importance of substrates in the fabrication and performance of optoelectronic devices.Item Effects of Purity on the Mechanical Properties of Single-Walled Carbon Nanotubes-Polymer Nanocomposites(British Journal of Applied Science & Technology, 2013) Yaya, A.; Dodoo-Arhin, D.; Onwona-Agyeman, B.; et al.This study investigated the superior mechanical properties of single-walled carbon nanotubes (SWCNTs), and its polymer nanocomposites using 0.5% and 1% loading of raw and purified SWCNTs in an epoxy matrix and the degree of dispersion. The extent of load transfer between the nanotubes and the matrix was studied by analyzing the second order G’-band ( 2550 cm-1) of Raman Spectroscopy. The samples have been characterized by structural (Raman spectroscopy), mechanical (tensile test), physical, and microstructural (SEM) point of view. Purified SWCNTs give a better-reinforcing potential compared to raw SWCNTs. We found an increase in Young’s Modulus (3780 MPa-4263 MPa) and toughness (62 MPa-68.8 MPa) for the nanocomposites prepared from purified SWCNTs.Item Fabrication and Characterisation of Ghanaian Bauxite Red Mud-Clay Composite Bricks for Construction Applications(American Journal of Materials Science, 2013) Dodoo-Arhin, D.; Konadu, D.S.; Annan, E.; et al.The behavior of Ghanaian-based bauxite red mud-Tetegbu clay composites has been investigated for their applicability in the ceramic brick construction industry as a means of recycling bauxite waste. The initial raw samples were characterized by X-ray diffraction (XRD), X-ray Fluorescence spectroscopy (XRF), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (Tg-DTA). The red mud-clay composites have been formulated as 80%-20%, 70%-30%, 60%-40%, 50%-50% and fired at sintering temperatures of 800ºC, 900ºC and 1100ºC. Generally, mechanical strengths (modulus of rupture) increased with higher sintering temperatures. The results obtained for various characterization analyses such as bulk densities of 1.59 g/cm3 and 1.51 g/cm3 compare very well with literature and hold potential in bauxite residue eco-friendly application for low-cost recyclable constructional materials.Item Computational Modelling of poly(9-vinylcarbazole)/Fullerene nanoheterojunction for organic solar cells and photovoltaics applications – A DFT Approach(SSRN Electronic Journal, 2022) Elloh, V.W.; Dodoo-Arhin, D.; Kan-Dapaah, K.; et al.Organic polymer photovoltaics have great technological potential as an alternative source of electrical energy. The demand for inexpensive, renewable energy sources is the driving force for new approaches in the production of low-cost polymer solar cells. During the quest to determine the best deposition and thermal annealing procedures for organic materials in organic devices, it has become increasingly clear that the structural order of these materials is a key factor. Highly ordered aggregation of conjugated oligomers and polymers can improve properties such as charge transfer and interaction with light processes that lead to better device performance. The development of such procedures for polymers and their blends although successful, has taken on a substantial try-and-error approach. Structural and morphological characterization of organic materials in the solid state is relevant for their application in Organic Photovoltaics. A comprehensive investigation of the PVK/C60 adsorption surface is performed using ab initio density functional theory calculations combined with van der Waals corrections (GGA+vdW). The goal is to use detailed atomistic computational approaches to model intrinsic electrical and optical properties, to investigate the influence of packing arrangements on the anisotropy of properties that relate to device performance, to elucidate the behavior of active materials during deposition and thermal treatment impacts on resulting morphologies which are relevant to the development of devices.Item Effect of mechanical activation on mullite formation in an alumina-silica ceramics system at lower temperature(World Journal of Engineering, 2016) Obada, D.O.; Dodoo-Arhin, D.; Dauda, M.; et al.Purpose – This work aims to analyze the effect of mechanical activation on structural disordering (amorphization) in an alumina-silica ceramics system and the formation of mullite most notably at a lower temperature using X-ray diffraction (XRD). Also, an objective of this work is to focus on a low-temperature fabrication route for the production of mullite powders. Design/methodology/approach – A batch composition of kaolin, alumina, and silica was manually pre-milled and then mechanically activated in a ball mill for 30 and 60 min. The activated samples were sintered at 1,150°C for a soaking period of 2 h. Mullite formation was characterized by XRD and scanning electron microscopy (SEM). Findings – It was determined that the mechanical activation increased the quantity of the mullite phase. SEM results revealed that short-milling times only helped in mixing the precursor powders and caused partial agglomeration, while longer milling times, however, resulted in greater agglomeration. Originality/value – It is noted that a manual pre-milling of approximately 20 min and a ball milling approach of 60 min milling time can be suggested as the optimum milling time for the temperature decrease succeeded in the production of mullite from the specific stoichiometric batch formed.Item Mechanical measurements of pure and kaolin reinforced hydroxyapatite-derived scaffolds: A comparative study(Materials Today: Proceedings, 2020) Obada, D.O.; Dodoo-Arhin, D.; Dauda, E.T.; et al.This study describes the mechanical properties of pure hydroxyapatite (HAp) and kaolin-reinforced hydroxyapatite (K-HAp) is produced from non-separated animal bones using compression pressure under different sintering regimes. The HAp microparticles were synthesized separately using a facile heat treatment method and reinforced with 15 wt% of beneficiated kaolin (HAp/15 wt% BK) using the sol-gel method. The HAp and K-HAp-derived scaffolds were fabricated by cold pressing with a compaction pressure of 500 Pa. Next, the scaffolds were sintered at 900 C, 1000 C, and 1100 C with a 2 h dwell time in the air atmosphere. Subsequently, the mechanical properties of the scaffolds were examined. The effect of sintering temperature and compaction pressure on the hardness and the compressive strength of the pure and reinforced HAp showed that at all points of measurement (with and without compaction pressure), the mechanical properties increased with an increase in sintering temperature, and the most significant mechanical properties were obtained at 1100 C. The values of hardness at the maximum sintering temperature (1100 C) are 0.93 and 1.09 GPa with and without the application of compaction pressure, respectively, for pure HAp-derived scaffolds and 0.74 and 0.78 GPa with and without the application of compaction pressure, for K-HAp-derived scaffolds. The compressive strength for K HAp had the value of 7.84 MPa as compared with 0.69 MPa for the non-reinforced HAp matrix with the application of compaction pressure (500 Pa). The findings show that the mechanical properties of the synthesized kaolin-reinforced HAp about the scaffolds produced with the low compaction pressure of 500 Pa are suitable for human trabecular bone. 2020 The Authors. Published by Elsevier Ltd. This is an open-access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by nc-and/4.0) Selection and Review under the responsibility of the scientific committee of the International. Conference & Exposition on Mechanical, Material, and Manufacturing Technology.
- «
- 1 (current)
- 2
- 3
- »