Theses
Permanent URI for this communityhttp://197.255.125.131:4000/handle/123456789/22146
A long essay or dissertation or thesis involving personal research, written by postgraduates of University of Ghana for a university degree.
Browse
5 results
Search Results
Item Photocatalytic degradation of Rhodamine dyes using zinc oxide nanoparticles(Materials Today: Proceedings, 2020) Dodoo-Arhin, D.; Asiedu, T.; Agyei-Tuffour, B.; et al.This paper presents the synthesis of nanocrystalline zinc oxide (ZnO) particles via the sol-gel method using zinc acetate as a precursor. The calcination temperature of the ZnO was varied to determine its effect on particle size. The resultant samples were characterized using X-ray diffraction (XRD), Fourier Transform Infrared (FTIR), UltraViolet–visible Spectroscopy (UV–Vis) and Scanning Electron Microscopy (SEM). Nanocrystalline wurtzite ZnO particles with crystallite sizes ranging from 16 nm to 30 nm were produced. The Energy Band gap of the synthesized zinc oxide nanoparticles decreased with increasing calcination temperature and crystallite size. SEM Micrographs showed rice-like microstructure morphology of ZnO nanoparticles. The usage of the ZnO nanoparticles as a photocatalyst was also explored in the degradation of Rhodamine B dye using UV light, with particular attention paid to the effect of particle size and catalyst load on the degradation efficiency of the dyes. The nanoparticles calcined at 400 C with a crystallite size of 16 nm resulted in the highest degradation efficiency of 95.41% when 0.2 g catalyst loading was applied. 2019 Elsevier Ltd. All rights reserved. Selection and peer review under the responsibility of the scientific committee of the International Symposium on Nanostructured, Nanoengineered, and Advanced MaterialsItem Modified nanostructured titania photocatalysts for aquatic disinfection applications(Materials Today: Proceedings, 2020) Dodoo-Arhin, D.; Bowen-Dodoo, E.; Agyei-Tuffour, B.; et al.According to SDG 6, everyone on earth should have access to safe and affordable drinking water. In sharing water-treatment technologies that lead to accomplishing this goal, it is imperative to devise ways of removing microbial contaminants such as E. coli from drinking water, especially in resource-limited settings that lack centralized water supply systems. One of the approaches is bacterial disinfection of water at the point of use. In this study, the bactericidal effects of the photocatalysis of titanium dioxide-based nanoparticles under UV and visible light are explored. Pristine and silver doped nanostructured mesoporous titanium dioxide (Ag-TiO2, TiO2) particles with high specific surface area and average crystallite domain size of 7.0–7.5 nm were prepared using the simple and cost-effective sol-gel technique followed by thermal treatment. The addition of Ag+ ions during the hydrolysis/condensation of the Ti(IV) molecular precursor led to the homogeneous dispersion of the Ag+ cations on the titania matrix. The As-prepared nanoparticles were characterized using X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) surface area analysis, Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), thermogravimetry, Fourier Transform Infra-Red (FTIR), and Raman Spectroscopy. X-ray diffraction, FTIR, and Raman spectroscopy confirmed that the crystalline structure of the TiO2 matrix corresponds to the anatase polymorph; however, the presence of the dopant led to an increase in the system disorder due to the rise in the concentration of oxygen vacancies. The As-prepared nanoparticles were used for Escherichia coli (E. coli) inactivation under dark and UV–visible light conditions. Under dark conditions, Ag-doped titania and pristine titania resulted in 95% and 64% E. coli population inactivity while under light conditions, 99% and 97% degradation respectively were observed. Taken together, these results demonstrate that, the synthesized TiO2 nanoparticles have promising applications in the light-mediated point-of-use inactivation of bacterial contaminants in water. 2019 Elsevier Ltd. All rights reserved. Selection and peer review under the responsibility of the scientific committee of the International Symposium on Nanostructured, Nanoengineered, and Advanced Materials.Item Effects of substrates on the performance of optoelectronic devices: A review(Cogent Engineering, 2020) Asare, J.; Agyei-Tuffour, B.; Dodoo-Arhin, D.; et al.This review discusses the effects of substrates on devices fabricated for optoelectronic applications. It includes the types and characteristics of substrates, synthesis, and fabrication of substrates, and the influence of substrates on the optical properties, surface morphology, and current-voltage behavior of optoelectronic devices. The study showed that two main types of substrates: planar and textured are commonly used in the industry. Flexibility, semi-rigidity, and rigidity are characteristics of the substrates and they vary in modulus, transparency, and texture. Whereas glass and metal substrates can be produced via melt casting, polydimethylsiloxane (PDMS), polyethylene terephthalate (PET), etc are produced by crosslinking polymer base materials with curing agents. The mechanical and current-voltage characteristics are also shown for planar and textured substrate-based devices. The textured substrates showed ridges, wrinkles, and buckled surface morphology whereas the planar showed uniform and largely flat morphology. Textured substrates also recorded higher optical absorbance and improved device efficiencies than planar substrates. The molecular configuration of the polymer chains is edged-on for planar substrates and edge-on and face-on for textured substrates. The findings and their implications have been discussed to highlight the importance of substrates in the fabrication and performance of optoelectronic devices.Item Cyclic-induced deformation and the degradation of Al-doped LLZO electrolytes in all-solid-state Li-metal batteries(Journal of Power Sources, 2023) Adjah, J.; Orisekeh, K.I.; Agyei-Tuffour, B.; et al.This paper presents the results of a study of the mechanical degradation of Li-oxide garnet solid electrolyte, Li7La3Zr2O12 (LLZO) in all-solid-state lithium metal batteries. A coupled thermo-electro-chemo-mechanical the model was used to analyze the stress-strain distribution and cracking phenomena within the electrolyte. A combination of in-situ/ex-situ microscopic observations, strain mapping, and finite element modeling was deployed to study the progressive deformation and cracking phenomena that occur as a result of electrochemical charging and discharging, thermal runaway, and joule heating phenomena. The results show that strains induced during discharge cycles are more significant than those induced during the charging phase. The accumulation of strains during charging and discharging is also shown to result ultimately in cracking that impedes Li-ion transport, while accelerating electrochemical degradation. The implications of these processes are discussed for the development of robust and durable all-solid-state batteries.Item Comparative analyses of rice husk cellulose fiber and kaolin particulate reinforced thermoplastic cassava starch biocomposites using the solution casting technique(Polymer Composites, 2021) Agyei-Tuffour, B.; Asante, J.T.; Nyankson, E.; et al.The potential of biodegradable packaging materials from thermoplastic cassava starch (TPS) reinforced with rice husk cellulose fibers (RHCF) and kaolin particu lates (KP) using the solution casting method has been presented. This involved the blending of TPS and RHCF/KP in a plasticizer of ~4 ml of glycerol and ~45 ml of distilled water at 125 C and stirred at 60 rpm until a gel was formed. The gel was cast into sheets and bone-shaped tensile specimens and allowed to dry for 5 days and characterized. The results show a semicrystalline structure for TPS with a ~36% increase in crystallinity after reinforcement. The O-H bond stretching and the C-H bending bonds due to starch–glycerol reactions were the common functional groups in TPS–RHCF biocomposites, and Si-O-C bonds were characteristics of the silica phase in the kaolin. The water vapor transmission rate (WVTR) reduced to ~34% with KP reinforcements from ~238 g/m.day to 177 g/m. day and to ~74 g/m.day and ~164% for TPS–RHCF. The strength increased with up to 50 wt% kaolin content; ~0.96 MPa yield strength and ~2.60 MPa ultimate tensile strength (UTS) were recorded. For the RHCF reinforced composites, TPS 50 wt% also showed high strengths of ~0.96 MPa yield strength and ~3.50 MPa UTS. The WVTR reduced as the content of kaolin was increased. Typically, from 0 to 30 wt% volume fraction of kaolin, the WVTR was reduced by ~34% to 177 g/m. day for TPS–kaolin and by ~164% to ~74 g/m.day in TPS–RHCF. The as-prepared biocomposites have the potential as good packaging materials.